Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Malibu, CA
Gate access control in Malibu means wiring keypads, card readers, and intercoms into gate systems that face salt corrosion from the Pacific on one side and fire-access retrofit requirements from LA County on the other. Most of the homes we work on fall into two groups: older PCH-fronting cottages from the 1950s and 60s with worn entry hardware, and canyon estates rebuilt after the Woolsey Fire that now carry heavy custom steel gates tied to sophisticated intercom and access systems. Call (805) 516-0855 and you’ll get a live person, a written price before any work starts, and a technician who documents every adjustment with photos.
Why Malibu Homes Are Different
Salt air is the constant. The onshore breeze off the Pacific carries chlorides that eat through motor housing seals, corrode hinge pins, and degrade wiring insulation years faster than the same components would fail in Agoura Hills or Westlake Village. A gate opener that might run twelve years inland often needs a motor replacement by year seven on Point Dume or along Broad Beach. We see steel gates with rust bloom at the weld joints and aluminum frames with electrolytic pitting where stainless fasteners meet the rail. The marine layer compounds it: moisture sits on components for hours every morning, even in August.
The second pressure is fire compliance. Malibu sits inside LA County Fire Department’s highest hazard severity zones. After Woolsey in 2018, enforcement tightened on powered gates needing Knox key-switch overrides so engines can force entry without waiting on a homeowner or a locksmith. A meaningful share of older canyon-estate gates in Malibu are technically non-compliant right now. The estate-management firms that oversee many PCH and canyon properties know this and call us to retrofit the access hardware without ripping out the gate itself. It’s a specific skillset: marine corrosion remediation paired with fire-access code work. You won’t find that combination on a standard gate-repair ticket in Thousand Oaks.
Our Main Malibu Services
Malibu homeowners call us most for the three jobs below. Each has its own detailed page, but here’s the short version of what the work involves in this city.
Gate Repair in Malibu
Most repair calls in Malibu start with either a gate that won’t open or a motor that’s getting louder. Salt corrosion and Santa Ana wind stress show up as failed hinges, sagging cantilever rails, and burnt circuit boards. We replace what’s actually worn, photograph the old part before it leaves the truck, and give you a written record of the part number installed. Gate Repair in Malibu covers the full scope.
Gate Installation in Malibu
New gate work on Malibu canyon lots means long driveway runs, steep grades, and usually a cantilever sliding configuration so the gate doesn’t drag on uneven ground. Coastal properties need marine-grade hardware from the first bolt. We measure, spec the right hardware for the exposure, and hand you a written price before any fabrication starts. Gate Installation in Malibu has the details.
Gate Motor & Opener in Malibu
Salt air kills motor housings and control boards fast here. We service LiftMaster, FAAC, BFT, DoorKing, Elite, Viking, and Ghost Controls openers already on the property rather than steering you toward a replacement you may not need. When a motor does fail, we replace it with a corrosion-rated unit and set the limit switches on site. Gate Motor & Opener in Malibu walks through it.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Malibu
Gate access control in Malibu means wiring the entry system your gate uses to decide who gets in: keypads, card readers, phone entry, and video intercoms, all tied to the gate motor and usually a battery backup. What makes Malibu different is the pairing of salt-accelerated corrosion with LA County Fire’s rapid-access requirements. Many canyon estates rebuilt after Woolsey now carry heavy gates with access systems installed by one contractor and automation by another, which leaves nobody responsible for the integration. That’s the work we do: make the keypad talk to the board, make the Knox switch work, and document every connection so the next technician doesn’t have to reverse-engineer it. Our Gate Access Control service covers this in detail. The price range for access work in Malibu runs from roughly $180 to $1,200 depending on whether we’re replacing a single component or wiring a full phone-entry system into an existing gate.
Keypad Entry
Signs you need it
Your keypad stops accepting codes, the buttons stick, or the housing has cracked from years of salt spray and sun.
What it costs in Malibu
Keypad replacement or rewiring in Malibu typically runs $180-$500 depending on whether we’re swapping the unit only or running new low-voltage wire to the control board.
How we do it
We remove the old keypad, check the wiring run for corrosion, install the new unit with sealed connectors, program the codes, and photograph the finished installation.
Remote Control
Signs you need it
Remotes work intermittently, lose their programming after a power cycle, or only function within a few feet of the gate.
What it costs in Malibu
Remote programming or a replacement receiver on a Malibu gate usually lands between $120 and $250 including the new transmitter.
How we do it
We test the receiver, check antenna placement for interference from coastal terrain, program the new remote, and write down the frequency and dip-switch setting for your records.
Phone Entry
Signs you need it
The gate calls a dead number, drops calls mid-ring, or the intercom works but the open command doesn’t reach the motor.
What it costs in Malibu
Phone-entry system repair or replacement in Malibu spans $350-$900 depending on whether we’re repairing the existing unit or installing a new cellular-capable controller.
How we do it
We trace the signal path from the entry station to the motor board, test the relay, replace what’s failed, reprogram the call sequence, and photograph the finished wiring.
What Gate Access Control Costs in Malibu
| Item | Typical range in Malibu |
|---|---|
| Keypad replacement or rewiring | $180-$500 |
| Remote programming / receiver swap | $120-$250 |
| Phone entry repair or new controller | $350-$900 |
Do I need a Knox key switch on my Malibu gate?
If your property sits in an LA County Fire hazard severity zone and the gate is powered, yes, you need a Knox key-switch or approved rapid-entry override. We can add one to most gates without replacing the motor or the access system for $200-$400.
Can you add a video intercom to an existing Malibu gate?
Yes, we wire video intercoms into existing gate systems routinely. The work runs $500-$1,200 depending on whether the cable run is already in place or we’re trenching from the driveway to the house.
Gate Parts & Welding in Malibu
Gate parts and welding in Malibu usually means rescuing a gate that’s still structurally sound but has failed at the joints, the hinges, or the hardware. Salt air concentrates its attack at exactly those points: the weld where a steel picket meets the rail, the hinge pin that’s been wearing against a corroded barrel, the roller that’s been dragging through sandy runoff from a canyon hillside. On PCH-fronting properties, we see rust through the bottom rail within a decade of installation. On canyon lots, the Santa Anas add mechanical fatigue on top of it. Our Gate Parts & Welding service replaces the failed component and leaves the surrounding material documented so you know what’s next. Most jobs in Malibu fall between $160 and $1,100 depending on the part and the amount of fabrication involved.
Hinge Replacement
Signs you need it
The gate sags, scrapes the ground, or the pivot point shows rust streaks and metal flaking.
What it costs in Malibu
Hinge replacement on a Malibu gate typically runs $160-$380 per hinge depending on gate weight and whether the post is sound enough to accept the new hardware.
How we do it
We support the gate, cut out the failed hinge, weld or bolt in the replacement, re-align the gate, and photograph the new installation against the old.
Post Replacement
Signs you need it
The post leans, wobbles at the base, or shows cracks through the concrete footing from wind load or corrosion swelling.
What it costs in Malibu
Post replacement on a Malibu gate usually runs $400-$900 including setting the new post in concrete and re-hanging the gate on the same day.
How we do it
We cut the old post at the footing, set a new galvanized or powder-coated post, brace it square, pour the footing, and re-mount the hinges once it’s set.
Custom Welding
Signs you need it
A cracked weld, a snapped picket, or a section of the gate frame that’s rusted through and needs new metal.
What it costs in Malibu
Custom welding repair in Malibu lands between $250 and $750 depending on the length of the weld, the material thickness, and whether we’re working in place or removing the gate section.
How we do it
We grind out the failed weld, cut out corroded material, weld in new steel to match, grind smooth, prime, and paint or powder-coat to match the existing finish.
What Gate Parts & Welding Costs in Malibu
| Item | Typical range in Malibu |
|---|---|
| Hinge replacement | $160-$380 per hinge |
| Post replacement | $400-$900 |
| Custom welding repair | $250-$750 |
Can you weld a cracked gate in place, or does it need to come off?
Most crack repairs can be welded in place. We brace the gate, grind the crack, weld it, and reinforce the back side. Full-section rebuilds are easier off the hinges, but we’ll tell you which one you need and what each costs before we start.
How long does a welded repair last in salt air?
With proper preparation, primer, and a marine-grade topcoat, a welded repair on a Malibu gate should last as long as the surrounding metal. The key is removing all rust before welding and sealing the repair so chlorides can’t get under the finish.
Brands We Service in Malibu
We service the opener that’s already on your Malibu property rather than pushing a replacement you don’t need. Most of the canyon estates and PCH-fronting homes we work on run Viking, DoorKing, Elite, or Ghost Controls automation. We stock common control boards, receivers, and safety-edge parts locally, which keeps most repair turnarounds to a single visit. Our brands page lists the full range.
Pricing for Gate Repair in Malibu, CA
| Service | Typical range in Malibu |
|---|---|
| Keypad replacement or rewiring | $180-$500 |
| Remote programming / receiver swap | $120-$250 |
| Phone entry repair or new controller | $350-$900 |
| Video intercom installation | $500-$1,200 |
| Knox key-switch retrofit | $200-$400 |
| Hinge replacement | $160-$380 per hinge |
| Post replacement | $400-$900 |
| Custom welding repair | $250-$750 |
| Gate roller replacement | $140-$320 |
What pushes a Malibu job toward the upper end of these ranges is exposure: a PCH-fronting gate that’s been in salt spray for a decade will need more corrosion removal before new parts go on, and a canyon estate gate with a long cable run adds labor hours. The price we quote is the price you pay: you get it in writing before a single tool comes off the truck, and it doesn’t change unless we find something that wasn’t visible at the start, at which point we stop and show you before proceeding.
Neighborhoods We Serve in Malibu
We run gate repair calls across the full length of Malibu, from the PCH corridor up into the canyon communities. Response time for most repair calls is same-day or next-morning depending on the season and the canyon access.
- Point Dume
- Broad Beach
- Malibu Park
- Malibu Colony
- Latigo Canyon
Service Area - Cities Near Malibu
Beyond Malibu proper, our crews cover the nearby coastal and canyon communities. We handle gate access and welding work in Agoura Hills, CA, Westlake Village, CA, Thousand Oaks, CA, and Calabasas, CA. Dispatch and scheduling are coordinated from our Los Angeles office; the technicians serving Malibu are local to this corridor.
Serving Malibu, CA - Our Local Coverage Area
We’re based in the Malibu area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Malibu
Most Malibu repair calls get same-day or next-morning response. We’re already running trucks along the PCH corridor and into the canyon communities every weekday, so we’re typically close by when a gate fails. Emergency calls are answered live at (805) 516-0855 any hour.
Straight repairs, hinge swaps, and motor replacements generally don’t trigger a permit. Full gate replacement or any work that changes the driveway footprint or adds a new power run can require city review. We’ll tell you what applies to your specific job and handle the coordination.
Yes, always. A written price is handed over before any work begins, and it’s the price you pay. If we find something hidden, we show you first and get your approval before proceeding. No invoice surprises at the end of a Malibu job. Call (805) 516-0855 for a free estimate on any gate work.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Malibu Customers Say
"The safety loop had never been installed correctly by the previous company. They showed me the reading, fixed it, and did not charge me for the diagnosis."
- Patrick H."They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C."Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."
- Camille R.